Log in or Sign up
Antiques Board
Home
Forums
>
Antique Forums
>
Furniture
>
Refinishing Tips/Advice help please
>
Reply to Thread
Message:
<p>[QUOTE="jcap7452, post: 1849683, member: 14526"]How is this for my step by step process? Please let me know if I should make any changes. Next I will be purchasing material listed in process.</p><p><br /></p><p>1. Scrub with soap and water</p><p>2. Wipe down with mineral spirits to remove oils or wax</p><p>3. Sand (medium grit sandpaper or steel wool w/ detail) get all gloss finish off</p><p>4. Wipe down with tack cloth to remove any dust</p><p>5. Paint with chalk paint</p><p>Or</p><p>5a) Paint on primer (Zinsser 00904 B-I-N Pigmented Shellac Primer-Sealer & Stain Killer, White, 1 Quart)</p><p>5b) Sand again using a fine-grit sandpaper & wipe down with tack cloth removing all dust</p><p>5c) Paint using interior latex paint in a semi-gloss finish with small foam roller on main parts and good brush on crevices </p><p>-Flat finish will show every fingerprint and flaw and will be harder to clean.</p><p>-The glossier the finish, the easier to clean.</p><p>-Paint thin coats, and repeat: sand between each coat! This step is very important if you want to achieve an even finish.</p><p>-Usually paint 2-3 coats total</p><p>6. Protect/Seal - let last coat of paint dry for at least 24 hours. (Or just leave it alone and let it cure for about 30 days). -If you are using a white or extremely light color of paint, do NOT use polyurethane to seal your finish. It can yellow over time. On any other paint color, it should be fine, recommend Minwax Wipe-On Poly because it is extremely easy to use. (nice Satin finish.) Water-based topcoat like Minwax Polycrylic is easier to clean up and there aren’t as many fumes.</p><p>-Another option, that can be used on any color including whites, is furniture wax. Minwax Finishing Wax, just wipe it on (use cheesecloth to apply it), let it dry for 10-15 minutes, and then buff it with a clean cloth until you get it as shiny as you want it.</p><p>7. FINISHED! After you’ve sealed your furniture, leave alone for a day or two before using</p><p><br /></p><p>**REMEMBER: Lightly sand your piece between EVERY SINGLE coat of paint. This helps you attain a much more professional and even finish. Be sure to remove the sanding dust each time[/QUOTE]</p><p><br /></p>
[QUOTE="jcap7452, post: 1849683, member: 14526"]How is this for my step by step process? Please let me know if I should make any changes. Next I will be purchasing material listed in process. 1. Scrub with soap and water 2. Wipe down with mineral spirits to remove oils or wax 3. Sand (medium grit sandpaper or steel wool w/ detail) get all gloss finish off 4. Wipe down with tack cloth to remove any dust 5. Paint with chalk paint Or 5a) Paint on primer (Zinsser 00904 B-I-N Pigmented Shellac Primer-Sealer & Stain Killer, White, 1 Quart) 5b) Sand again using a fine-grit sandpaper & wipe down with tack cloth removing all dust 5c) Paint using interior latex paint in a semi-gloss finish with small foam roller on main parts and good brush on crevices -Flat finish will show every fingerprint and flaw and will be harder to clean. -The glossier the finish, the easier to clean. -Paint thin coats, and repeat: sand between each coat! This step is very important if you want to achieve an even finish. -Usually paint 2-3 coats total 6. Protect/Seal - let last coat of paint dry for at least 24 hours. (Or just leave it alone and let it cure for about 30 days). -If you are using a white or extremely light color of paint, do NOT use polyurethane to seal your finish. It can yellow over time. On any other paint color, it should be fine, recommend Minwax Wipe-On Poly because it is extremely easy to use. (nice Satin finish.) Water-based topcoat like Minwax Polycrylic is easier to clean up and there aren’t as many fumes. -Another option, that can be used on any color including whites, is furniture wax. Minwax Finishing Wax, just wipe it on (use cheesecloth to apply it), let it dry for 10-15 minutes, and then buff it with a clean cloth until you get it as shiny as you want it. 7. FINISHED! After you’ve sealed your furniture, leave alone for a day or two before using **REMEMBER: Lightly sand your piece between EVERY SINGLE coat of paint. This helps you attain a much more professional and even finish. Be sure to remove the sanding dust each time[/QUOTE]
Your name or email address:
Do you already have an account?
No, create an account now.
Yes, my password is:
Forgot your password?
Stay logged in
Antiques Board
Home
Forums
>
Antique Forums
>
Furniture
>
Refinishing Tips/Advice help please
>
Home
Home
Quick Links
Search Forums
Recent Activity
Recent Posts
Forums
Forums
Quick Links
Search Forums
Recent Posts
Gallery
Gallery
Quick Links
Search Media
New Media
Members
Members
Quick Links
Notable Members
Registered Members
Current Visitors
Recent Activity
New Profile Posts
Menu
Search
Search titles only
Posted by Member:
Separate names with a comma.
Newer Than:
Search this thread only
Search this forum only
Display results as threads
Useful Searches
Recent Posts
More...